Installing a Water Softener – Preparation

Finding a Pro to Do the Install. Shut off the water to your house at the main line.

Water Softener Installation | How to Hook Up a Water Softener

Drain your pipes by opening up the lowest valve in the house and letting the water run out. Shut off your hot water heater and turn off the power leading to it. Locate the area along the main line where you want to install the water softener. Keep in mind this needs to be before the line feeds into the hot water heater. Cut into the main line using a pipe cutter. Tighten the cutter onto the pipe, then rotate it around until the pipe is cut through.

Catch any water that comes out of the pipe in a bucket. Install an elbow fitting in the line. This will allow you to feed the filter and have a bypass valve that will let you feed water around the filter if necessary. Measure the pipes that will lead to the bypass valve taking the measurements from the unit. Cut the pipes to fit, and solder on any nipples and fittings before you connect the pipe to the bypass valve.

Attach the pipes to the unit using compression fittings, which should be supplied with the unit. Clamp the hose to the unit, then feed it to where it will drain. Options include a floor drain, utility sink, or sump pump. The end of the hose will have to be at least two inches above the drain hole to prevent back siphoning of the water. Make sure the hose is securely clamped. Connect the overflow tube to the brine tank.

Turn the valve to the bypass position and flush water through it to remove any sediment or debris. Plug in the unit and set the valve to the backwash position. Open the valve up very slowly to let water in while releasing any air in the pipes. Tubing or copper pipe Teflon tape.

Water Softener Installation – A DIY Guide on How to Install a Water Softener

Set up the components of the system in the area you want to have them installed. Shut off the main water to your home , and drain the water out of the pipes by opening up the lowest spout in the house and allowing the water to run out. Tighten the pipe cutter onto the pipe and rotate it around the pipe to make the cut. Attach a shut-off valve to the pipe , either by gluing it to PVC, or by soldering it to copper. Install the carbon pre-filter after the shut-off valve , attaching it using compression fittings.

Install a second shut-off valve after the pre-filter , then extend pipe to the distribution head of the filter system. Attach it with a compression fitting.

Connect the down flow outlet of the system back to the cold water supply pipe so that the water will flow through the system and back through the house. Close both shut off valves and turn on the main water valve for the house.

How to install a water softener

Slowly open the shut off valves one at a time and check for leaks. If none are found, open the valves all the way to start the system.

Installing a Magnetic System. Locate the area where you want to install the magnetic system. Open up the magnet box according to the instructions. Professional installation is provided by screened, licensed, independent contractors who will provide you with quality service and a worry-free experience.

Each of these plumbing types may require different materials and different tools for installation. A drain is necessary for the regeneration or recharge process. The drain should not be more than 30 feet away from the softener and the drain line should not be elevated more than 8 feet above the floor. The power cord transformer needs to be plugged into a V continuous live outlet. Newer homes that have an easy-to-access plumbing loop are the best-case scenario.

You can save money by purchasing your softener plus the installation service in a bundle. Oftentimes, you also receive free system delivery, setup and programming, and free removal of your old device. Installation costs should include expenses for materials, labor, debris removal, and disposal of your old softener.

Electrical modifications or modifications to the plumbing system as well as inspection fees are generally not included. For the best result, make sure to hire a plumber that is trustworthy, licensed, insured, and experienced enough to complete the task. Many providers also offer a one-year warranty on their labor.

Do-It-Yourself (DIY) Installation

Maybe you can ask friends or co-workers for recommendations. And to get the best price, get a couple of cost estimates from different companies before you choose your favorite. Save my name, email, and website in this browser for the next time I comment. On this page you will learn: How to prepare for the installation Where to put a water softener How to install a water softener step by step Installing salt-free softeners How hard is it to install a water softener How long does it take to install a water softener Water Softener Installation Cost How much does it cost to install a water softener Who installs water softeners Installing a Water Softener — Preparation Please Beware that there Are Some Water Softener Brands that Require You to Hire a Licensed Plumber to Do the Installation.

This includes gathering the following tools and supplies: Depending on the plumbing material, you also require: So, shut off the entire water supply to your home first. Turn off your electric water heater — If you have an electric water heater, turn it off to protect it from getting damaged.

Where To Install A Water Softening System

Drain the water in all involved lines — Next open all faucets to drain away all the remaining water. This little precaution can save you real money in case anything goes wrong. Install the bypass valve — If not already in place, install the bypass valve on top of the softener, usually on the back of the unit and use the provided clips to secure it. The valve allows you to shut off the water supply to the system in case it requires maintenance or reparation without disturbing the water supply to your home. Please note that not all devices come with a bypass valve, however, in some areas you are required by law to have one, so that your softener can be easily turned off in case of emergency.

Put the softener in place — Put the softener in position and measure the length of all pipe connections that you need to make. Also tie in the brine line to connect the brine tank with the resin tank. For the pipe connections you can either use hard or flexible tubing. The latter allows you to remove the system more easily, but you will need to install extra adapters to your water line to screw it on.

If you prefer hard tubing, be careful to not damage any plastic parts when soldering.